Rigid, fixed-length guide combs: Earlier versions of this guide favored trimmers with multiple, fixed-length guide combs, which determine how much beard is left after a pass of the trimmer.A slim design offers more visibility in front of a mirror and allows you to better monitor where you’re cutting, but a too-slim design can be difficult to grip securely. A slim, robust design: We like trimmers that are slender in shape but also durable enough to last years without breaking if dropped.A powerful motor: We wanted a tool with enough oomph to cut through the coarsest hair, without pulling and without requiring multiple passes.Do not short-circuit, as this may cause burns. ![]() Do not burn or mutilate, as they may burst or release toxic materials. Wires may also be cut.ĬAUTION: THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED OF IN ACCORDANCE WITH STATE AND LOCAL REGULATIONS. ■ Lift the rubber side panels from their cradles and put them aside. ■ Pull or gently pry the trimmer halves apart, exposing the batteries. ■ Using a small Phillips head screwdriver, remove the four screws from the trimmer (2 in back, 2 under the comb). ■ Remove the trimmer guard as instructed in the section Removing Trimmer Guard Attachment. ■ Make sure your trimmer is unplugged from any outlets so you don’t risk an electric shock. The following procedure should be followed for battery removal: (MB-30, MB-35, MB-40, MB-45, MB-50) When your rechargeable Beard & Mustache Trimmer reaches the end of its useful life, the batteries must be removed from the shaver and recycled or disposed of properly in accordance with your local and state requirements. Continue to charge the trimmer for 24 hours. After three minutes, turn ON/OFF switch on, then off. Connect the charger to the trimmer and plug the charger into a 120 VAC outlet. If the MB-50 trimmer requires charging, but the charger light does not glow when the charging adapter is connected, the batteries may have been severely discharged or not recharged for a long period of time. Clean the unit as directed in Cleaning and Maintenance section.Ĭall 1-80 for the authorized Remington Service Center closest to you or contact one of the Remington Service Centers provided on the enclosed card accompanying this package. Trimmer cutters do not move: ■ The cutting unit may be dirty and clogged. ■ Contact an authorized Remington Service Center regarding battery replacement (see enclosed card for the nearest location). ■ If battery power has been depleted, replace with 2 “AA” alkaline batteries (see Battery section). Trimmer will not operate unless batteries are correctly positioned. The trimmer does not work when turned on: ■ Be certain batteries have been properly installed. Contact an authorized Remington Service Center (see separate card in this package for the location nearest you). If time between recharging cycles does not increase, battery may need replacing. Trimmer does not hold charge: ■ Fully discharge battery by running trimmer until it stops then follow recharging instructions (see section on To Charge/Recharge). Clean the unit as directed in Cleaning & Maintenance section. The trimmer does not work when turned on: ■ Trimmer must be charged for a full 14-16 hours- MB-30, MB-35, MB- 40 and MB-45 (3 HRS for MB-50). ■ Brush any hair from the trimmer blades and blow out any hairs from the recess that holds the trimmer in retracted position. Miniature Trimmer (MB-40, MB-45, MB-50) ■ Flip the miniature trimmer up into operating position. ![]() Do not rinse the cutter assembly under water or use cleaning fluids, which could remove the lubrication. Brush out any remaining hair from the cutter teeth and hair pocket with the brush provided. ![]() Blow out any loose hair that has accumulated. The cutter assembly will swing up and the underside of the cutter assembly will be accessible. Flip the blades open by pushing upward on the cutter teeth. Remove trimmer guard attachment from trimmer. Weekly Trimmer should always be shut off. ■ Do not use liquid cleaners on the cutters or harsh or corrosive chemicals on the unit’s main body. ■ Do not apply pressure or hard objects to the cutters. Clean your trimmer regularly to ensure that the unit’s operating life is not prematurely shortened. Cleaning should only be done with a soft brush, such as the brush supplied with the unit. Your trimmer is fitted with high-quality hardened steel or ceramic cutting blades that are permanently lubricated.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |